Bar Blenders
Models 901/908/909/910/918/919
Operation Manual
Page 2
Mélangeurs pour bar
Modèles 901/908/909/910/918/919
Manuel d’utilisation
Page 10
Licuadoras para bar
Modelos 901/908/909/910/918/919
Manual de uso
Página 18
840111500
Blender Safety
IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using electrical appliances, basic safety precautions should be followed, including
the following:
• To prevent damage to blender, jar, or cutter
assembly, DO NOT move or shake blender
while in operation. If blending action stops during
operation, turn blender OFF, remove jar from
base, remove jar cover, and use a thin rubber
spatula to push mixture towards cutters.
• Do not spray the base with a high-pressure
spray gun.
• Disconnect power before cleaning or servicing.
• To prevent burns from hot liquids splashing out
of the jar, always remove the filler cap of the
container cover before blending hot liquids.
• Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions,
or is dropped or damaged in any manner.
Return appliance to the nearest service facility
for examination, repair, or electrical or
mechanical adjustment.
• If the supply cord of this appliance is damaged,
it must be replaced by the manufacturer or its ser-
vice agent or a similar qualified person. If fitted
with a non-rewirable U.K. plug, the 13 amp fuse
approved by ASTA to be B.S. 1362 must be used.
If you need a replacement fuse carrier, it must be
replaced by the same colour coded carrier with
the same markings. Fuse covers and carriers
can be obtained from approved service agents.
IMPORTANT: If the molded plug is cut off,
dispose of it immediately. The plug is not rewirable
and would cause a shock hazard if inserted into
a socket.
• Read all instructions.
• Plug into a grounded outlet.
• Do not touch surfaces that may be hot.
Use handles or knobs provided.
• Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
• Do not use appliance for other than intended use.
• To protect against electrical shock, do not
immerse cord, plug, or blender base in water
or any other liquid.
• Close supervision is necessary when any
appliance is used by or near children.
• The use of accessory attachments not recom-
mended by Hamilton Beach may cause injuries.
• To reduce risk of personal injury, unplug cord
from outlet when not in use, and before putting on
or taking off parts or doing any other servicing of
the blender.
• Do not let cord hang over edge of table or
counter or touch hot surfaces.
• Do not place on or near a hot gas or electric
burner or in a heated oven.
• To reduce risk of personal injury and to prevent
damage to blender or jar and cutter assembly,
DO NOT insert utensils into blender jar while
operating blender, or store utensils in the blender
jar when it is not in use.
• Avoid contacting moving parts.
• Blades are sharp. Handle carefully.
• Inspect jar and cutter assembly daily. Check
cutter for wear, nicks, or broken blades. Replace
jar and cutter assembly at least every 12 months.
• Do not defeat the jar pad sensors.
• Do not use outdoors.
• For a complete operation manual in this
language, please visit our website at
or call 910-692-2223.
• This appliance is intended for short periods
of operation, with a rated operating time of
3 minutes.
– SAVE THESE INSTRUCTIONS –
Blender Operation – Quick Start Guide
1. Place the blender on a dry, level surface.
4. Set the controls to your preference.
5. Move the power switch to the “on” or I position.
2. Make sure the power switch is in the “off” or O
position. Plug the blender into a grounded electrical
outlet.
3. Place the jar on the base with ingredients and jar
lid in place.
3
Parts and Features
The parts and features for the 901/908/909/910/918/919 Blenders are shown on this page. Become familiar
with all parts and features before using your blender.
Your blender is designed for blending and mixing beverages.
Note: The Blender is not designed to crush ice. Ice cubes made in most icemakers may be added to liquid
ingredients in the blender to make daiquiris or similar drinks.
Cutter Unit Assembly
Gasket
Removable
Filler Cap
Cover
Blades
Clutch
Container
Model 901
Blender
Base
On/Off
Switch
Models
908/909
On/Off
Switch
Models 910/918/919
On/Off/Pulse Switch
HIGH/LOW
Switch
Model 908
Model 909
Model 910
Model 918
Model 919
Model 901
4
Operation
Operating the Blender
wWARNING
wWARNING
Cut Hazard
Electrical Shock Hazard
Plug into a grounded outlet.
Do not remove ground.
Always place cover on jar when blending.
Do not put hands, spoons or other utensils
in jar when blending.
Do not use an adapter.
Failure to follow these instructions can
result in broken bones or cuts.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire, or electrical shock.
Controls
Model 901:
ON/OFF
HIGH/LOW
Switch
• The ON/OFF switch will turn the blender ON for
continuous operation at approximately 18,000
RPM, or OFF.
Switch
ON/OFF
Switch
Models 908, 909, 910, 918, 919:
Two separate switches on the front panel allow
you to control the blender for precise blending
requirements:
Model 901
Models 908/909
• The ON/OFF switch will turn the blender ON for
3. Plug the blender into an
continuous operation or OFF.
electric outlet.
• The HIGH.LOW switch allows you to select the
following speeds:
4. Place the ingredients to be
blended into container.
5. Place the container onto
the base. Make sure it
rests securely on the base.
ON/OFF/
Pulse
Switch
Hi – 17,800 RPM Low – 11,500 RPM
HIGH/LOW
Switch
• The Pulse switch (Models 910, 918 and 919)
turns on the blender only when the switch is
pressed. When the switch is released, the blender
will stop. This will allow you to precisely control
the operation of the blender.
6. Place the cover and filler
cap on the container.
Models 910/918/919
7. Set the Hi/Low switch
Using the blender
(except model 901) to the
Before you use the blender for the first time, wash
the container, cover, and cutter unit assembly. Refer
to “Cleaning the Blender.” Do not put the cutter unit
assembly in the dishwasher.
To operate the blender, proceed as follows:
1. Place the blender on a clean, dry, level surface,
and set the ON/OFF switch to OFF.
desired speed. See “Professional Blending
Techniques” for blending tips.
NOTE: If you want the blender to run for short
bursts, press the Pulse switch (on some models).
While you are pressing the Pulse switch, the blender
will run at the selected speed. Release the Pulse
switch to stop the blender.
2. Place cutter unit in the threaded collar, blades up.
Slip the gasket OVER the blades and onto the
base of the cutter unit. Screw the completed
blade assembly onto the container.
5
Operating the Blender
Professional Blending Techniques
Filling the container
When filling the container with ingredients, follow
these recommendations:
• Use sufficient amount of liquid to ensure that the
mixture is fluid and free-running at all times. Pour
the liquid into the container FIRST.
wWARNING
• Cut solid ingredients into pieces that are no
bigger than a 1″ (2.5cm)cube.
• Add the ingredients to container in batches. Do not
blend maximum volume all at once.
Burn Hazard
• Do NOT overfill the container with product. This
may prevent the blender from processing the
product properly. Process dense foods or thick
mixtures in small batches, and remember that the
volume of the product normally increases during
processing.
• Do not exceed one quart of content when
blending hot product.
• Always place the cover and filler cap on the
container when blending. For blending hot
liquids, remove filler cap from container cover
before blending.
Always use caution when blending
hot contents.
Failure to follow these instructions
can result in burns.
Blending hot mixtures
IMPORTANT: To minimize the possibility of
scalding, the following precautions MUST be
observed:
• Do not exceed 1 quart of content when blending
hot product. Remember that the volume of the
product normally increases during processing.
Blending techniques
Icy drinks – Do not use blender to crush large ice
cubes. The blender is not designed for this. Small
ice cubes or crushed ice is recommended. Pour in
liquid, then add ice. Cover. Set speed at HIGH
(except model 901) and process until desired
consistency is reached. Chunks of frozen fruit can
be added to milk or fruit juice to produce a sherbet
or slush.
• Always place the cover on the container and
remove the filler cap from container cover when
blending hot liquids to prevent the build up of
pressure.
• Never stand with your face directly over the
container when operating the blender where
steam may be released.
• Begin on LOW speed and then select a speed
that produces a column of air in the center of
the container.
Filler Cap
Use the filler cap to add liquids to the container
while the unit is running.
6
Caring for the Blender
Cleaning Instructions
wWARNING
wWARNING
Cut Hazard
Electrical Shock Hazard
Plug into a grounded outlet.
Do not remove ground.
Always place cover on jar when blending.
Do not put hands, spoons or other utensils
in jar when blending.
Do not use an adapter.
Failure to follow these instructions can
result in broken bones or cuts.
Do not use an extension cord.
Do not immerse base in water or
other liquid.
Failure to follow these instructions can
result in death, fire, or electrical shock.
Sanitizing
1. Wash container as instructed in “General
Cleaning.”
General cleaning
2. Fill container with sanitizing solution (See
“Recommended Sanitizing Solution” below)
and place on base.
3. Replace cover and filler cap and run on LOW
(except model 901) speed for 2 minutes. Empty
container.
Do not allow food residue to dry on any part of the
blender. Wash and rinse container, cutter unit
assembly and base after each use, or whenever it
will not be used again within one hour, as follows:
1. Remove the container from the base, and then
remove the cover. Add cleaning solution to the
container. Use a washing solution of hot water
(less than 115° F/46° C) and a non-sudsing
detergent. Use the recommended amount of
detergent.
4. Wipe the container exterior with a soft cloth or
sponge dampened with sanitizing solution.
5. Immerse the cover and filler cap in sanitizing
solution for two minutes.
6. Remove any remaining moisture from cutter
assembly by replacing container on base with
cover and filler cap in place. Then run blender
on HiGH (except model 901) speed for a minimum
of 2 minutes.
2. Scrub and flush out the container interior,
cover and filler cap to remove food residue.
Empty container.
3. Fill container 1⁄4 full with fresh washing solution
and place it on the base.
7. To dry, place empty container on base and run on
4. Replace the cover on the container and run the
blender on high speed (except model 901) for 2
minutes.
HIGH (except model 901) speed for two seconds.
8. When ready to use, rinse with clean water.
5. Repeat step 3 using clean rinse water
NOTE: Do not rinse container, cover or filler cap
(95° F/35° C).
after sanitizing.
6. Wipe down the container, filler cap, and cover
with a soft cloth or sponge, dampened with fresh
washing solution.
7. Wipe the exterior of the base with a damp cloth
or sponge. The base contains electrical
components: do not immerse, use a
high-pressure washer, or use a dishwasher
to clean the base.
Recommended Sanitizing Solution:
The sanitizing solution should consist of 1
tablespoon of household bleach per 1 gallon of
clean, cool water (60° F, 16° C) mixed according
to the instructions on the bleach. When using a
sanitizing solution other than that recommended,
the sanitizing solution concentration should be
tested using commercially available test strips
and should indicate a concentration between
100 and 200 parts per million of bleach to water.
7
Caring for the Blender
Troubleshooting Guide
Problem . . .
Solution . . .
• Check to see if unit is securely plugged into an electric outlet.
Blender fails to start
or stops while it is
running and cannot
be restarted
• Check to see if the fuse for the electric outlet has blown or if a
circuit breaker has tripped.
Ingredients will not mix
properly
• Check to see if enough liquid has been added to the ingredients. Mixture should
be fluid and free-running at all times.
• Solid pieces are too large. Pieces should not exceed 1″ (2.5 cm) cubes.
• Container is too full. Do not fill past highest graduation marking.
• Cutter unit blades are not sharp or are damaged. Inspect container and cutter
assembly daily. Replace container and cutter assembly at least every 12 months
or sooner if cutter assembly appears worn or damaged.
• Check to see if cutter unit assembly is installed properly.
• Select speed (on some models) to create a fluid blend.
Maintenance
Inspect the blender and its various parts and replace as follows:
Daily
Unplug the blender and remove the container from the base, and then inspect the container and
cutter unit assembly for wear, nicks, and broken or loose blades. Replace if necessary. If the
cutter assembly blades are loose, discontinue use immediately and replace the cutter assembly.
Do not attempt to repair or tighten the cutter assembly. See “Replacement Parts” below.
Weekly Unplug the blender, and then inspect the power cord insulation and power plug for cracks.
Refer to “Requesting Assistance or Service” for repair or replacement.
Yearly
Replace the container and cutter unit assembly at least once a year. See “Replacement Parts”
below.
Replacement Parts
Refer to “Requesting Assistance or Service” to order parts below.
Model Part Description
Part Number
901
908
909
910
918
919
ALL
1 container
6126-901
6126-908
6126-909
6126-910
98000
1 container
1 container
1 container
1 container
1 container
98100
Cutter unit assembly
99100
8
Product Warranty
This Warranty supercedes all other Product Warranties
LIMITED WARRANTY
This product is warranted to be free from defects in material and workmanship for a period of one (1) year from the
date of original purchase, except as noted below. During this period, we will repair or replace this product, at our
option, at no cost to you. THE FOREGOING WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, WHETHER
EXPRESS OR IMPLIED, WRITTEN OR ORAL INCLUDING ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ANY LIABILITY IS EXPRESSLY LIMITED TO AN AMOUNT EQUAL
TO THE PURCHASE PRICE PAID, AND ALL CLAIMS FOR SPECIAL,INCIDENTAL AND CONSEQUENTIAL
DAMAGES ARE HEREBY EXCLUDED. There is no warranty with respect to the following, which may be supplied
with this product: (motor brushes, container and cutter assembly, clutches, bristle brushes, funnel, stainless steel
cup, agitators, carafes, etc.). This warranty extends only to the original purchaser and does not cover a defect
resulting from abuse, misuse, neglect, unauthorized repair, or use not in conformity with the printed directions.
Always use this product in the manner provided in the Operation Manual. This warranty gives you specific legal
rights and you may also have other legal rights which vary from state to state, or province to province. Some states
do not allow limitations on implied warranties or special, incidental or consequential damages, so the foregoing
limitations may not apply to you.
If you have a claim under this warranty please contact our CUSTOMER SERVICE DEPARTMENT at
1-866-285-1087. (For faster service please have model, series, and type numbers ready for operator to
assist you.) Reasonable proof of date of purchase must be presented; otherwise the effective date of
the warranty will be based upon the date of manufacture plus ninety (90) days.
Hamilton Beach/Proctor-Silex, Inc.
Commercial Customer Service
263 Yadkin Road
Southern Pines, NC 28387
5/03
9
|