Guardian Technologies Vacuum Cleaner GGU350TT User Manual

USE & CARE INSTRUCTIONS  
®
Germ Guardian  
2-in-1 Upright  
and Canister  
with Silver Clean Technology  
English  
French  
Spanish  
E - 1  
F - 1  
S - 1  
Replacement Parts:  
HEPA Dirt Cup Filter FLTB  
Exhaust Filter FLTA  
Belt BLT1  
Model No. GGU350TT  
1-Year Limited Warranty  
1.866.603.5900  
REV0609  
!
WARNING:  
Date Purchased  
Cleaner assembly may include  
small parts. Small parts can  
present a choking hazard.  
month ________  
E-1  
year _________  
 
plEaSE rEad all inSTrucTionS bEForE uSinG ThiS appliancE  
HoSE CRADLE ASSEMBLy  
WARNING! Do not use the Dirt Cup Handle to move the cleaner.  
HoSE CRADLE ASSEMBLy  
THERMAL RESET BUTToN:  
Set hose cradle on the top of the cleaner. (Fig. 1)  
using a phillips screwdriver, secure the 3/4-inch screw.  
Operates due to overheating, caused by a full dirt cup, clogged filter or blocked pipes.  
Unplug the cleaner and remove the blocked materials. To operate again, after  
cooling down the cleaner about 30 minutes, press the Thermal Reset Button.  
Model .................................................. GGU350TT Cord Length .............................................. 32 feet  
Rating .................................................. 120V/60Hz Inner Filter .......................................... HEPA Filter  
Amperage ............................................... 12 amps Exhaust Filter .................................. Micron Filter  
Weight (Net) .......................................... 20.50 lbs Headlight ......................................................... Yes  
Dimensions ............................. 15" x 14" x 45.25" Belt .................................................................... Yes  
Fig. 1  
VACUUM ASSEMBLy: UPRIGHT USE  
HoSE ASSEMBLy  
Handle  
Cord Clip  
Main Power Brush Power  
Switch Switch  
Handle Hose Connector  
(TOOLS/CANISTER MODE)  
Handle  
Extension  
Button  
W
E
B
Handle Inlet  
HoSE ASSEMBLy  
Hose Connector  
insert the body end of the hose into the hose inlet on the top of the cleaner. (Fig. 2)  
Canister  
Handle  
line up circular tab on hose cuff with inner groove. (Fig. 2)  
connect and twist clockwise to secure proper hose connection. (Fig.3)  
place hose in hose cradle. (Fig. 4)  
Hose Cradle  
Hose  
insert the base end of the hose into the hose inlet on the base of the cleaner. (Fig. 5)  
Dirt Cup  
Hose Clip  
Filter  
Dirt Cup Handle  
Handle Removal  
Button  
IMPoRTANT: hose must be connected to inlet on base of vacuum to work in the upriGhT  
mode.  
Body  
Knob  
Cord  
Storage  
Hooks  
Height Adjustment  
Base Hose  
Connector  
(UPRIGHT MODE)  
Handle Release  
Pedal  
Canister  
Release Pedal  
Headlight  
Thermal Reset  
Button  
Base  
Hose  
Cord  
Plug  
Fig. 3  
Fig. 2  
Base Hose  
Connector  
Fig. 5  
Detail of  
Hose Lock  
Fig. 4  
E-4  
E-5  
 
VACUUM ASSEMBLy: UPRIGHT USE (CoNTD)  
TooL ASSEMBLy  
HANDLE ASSEMBLy  
HANDLE ASSEMBLy  
insert handle in the handle inlet on the top of the body. (Fig. 6)  
TooL ASSEMBLy  
attach crevice tool, dusting brush and upholstery brush into  
storage area on the back of the vacuum. (Fig. 8)  
Handle  
HANDLE DISASSEMBLy  
Crevice  
Tool  
push the handle removal button.  
pull handle upward to remove.  
Dusting  
Brush  
Fig. 8  
Protrustion to Lock  
Handle Inlet  
Upholstery  
Brush  
Handle  
Removal  
Button  
USING IN UPRIGHT MoDE  
USING IN UPRIGHT MoDE  
push the handle release pedal (Fig. 9)  
Turn main power switch on. Turn brush power switch on.  
CAUTIoN: The headlight and brush does not come on when in the upright  
position even if the switch is on. you must release the handle for the brushroll  
to begin spinning. (Fig. 10)  
Fig. 6  
BASE ASSEMBLy  
BASE ASSEMBLy  
Set the body on the top of the base. (Fig. 7)  
use both sides of the guide feature on the  
base to align.  
Base Safety  
Switch  
Base  
Handle Release  
Pedal  
Fig. 9  
Fig. 10  
Base  
BASE DISASSEMBLy  
push the release canister pedal.  
lift up and remove the body.  
Guides  
HEIGHT ADJUSTMENT KNoB  
Canister  
Release Pedal  
HEIGHT ADJUSTMENT KNoB  
rotate the height adjustment knob to the correct carpet height. (Fig. 11)  
To clean bare floor, set this knob to the bare floor position and turn off the brush power  
switch. (located on the top of the cleaner - see page 2)  
Fig. 7  
Fig. 11  
E-6  
E-7  
 
UPRIGHT MoDE: TooL USAGE  
SToRING IN UPRIGHT MoDE  
after using the vacuum, store in upright mode.  
Store accessories on the storage clips located on the vacuum body.  
Wrap the cord around the cord storage hooks on the side of the body and hang the  
plug at the cord clip on the wand. (Fig. 18)  
TooL USAGE  
1. Turn brush oFF.  
2. remove hose from base hose connector on the lower portion of the cleaner. (Fig. 12)  
3. remove handle from cleaner: push handle removal button and pull up on handle to  
disconnect from body. (Fig. 13)  
4. insert hose into handle hose connector and twist clockwise to lock in position. (Fig. 14)  
5. push button on wand to extend telescoping wand. (Fig. 15)  
6. Select the tool needed for above-floor cleaning and attach to end of wand.  
Hose  
Handle Hose  
Connector  
Cord Clip  
Handle  
Telescoping  
Button  
Handle  
Hard Floor  
Nozzle  
Handle  
Handle  
Removal  
Button  
Hose  
Base Hose  
Connector  
Cord  
Plug  
Fig. 12  
Fig. 13  
Fig. 14  
Fig. 15  
Fig. 18  
CoNVERTING To CANISTER MoDE  
CoNVERTING To CANISTER MoDE  
1. remove hose from base hose connector. (Fig. 16)  
2. Step on canister release pedal and pull body upward by canister handle. (Fig. 17)  
3. Follow steps 3-5 in upriGhT modE: Tool uSaGE section. (See above)  
4. insert end of handle into hard floor nozzle.  
5. canister mode.  
Canister  
Handle  
Body  
Hose  
Canister Release  
Pedal  
Base Hose  
Connector  
Base  
Fig. 16  
Fig. 17  
IMPoRTANT:  
When returning to UPRIGHT mode hose MUST be removed  
from handle and returned to inlet on body.  
E-9  
E-8  
 
CLEANING & REPLACING FILTER  
CLEANING DIRT CUP  
To oPTIMIzE THE VACUUM PERFoRMANCE yoU SHoULD CLEAN THE  
FILTER EACH TIME yoU EMPTy THE DIRT CUP.  
you will need to empty dirt cup when dust reaches the Full line.  
Turn oFF the vacuum and unplug from electrical outlet.  
Grasp the dirt cup handle and depress button, pull out the dirt cup from  
the body. (Fig. 19)  
1. lift up the dirt cup cover, rotate and remove the filter protector.  
2. rotate and remove the inner filter. (Fig. 21)  
Tap the inner filter on a trash bin to remove the dust from the pleats. (Fig. 22)  
To empty, remove the dirt cup and hold over trash bin. push the dirt release  
button and dispose of the dirt. (Fig. 20)  
NoTE: This inner filter is washable and can be rinsed if you notice a reduction in  
vacuum performance (suction). To wash, first tap lter to remove excess dirt and  
dust from pleats. rinse filter clean with warm water then allow to completely dry  
(a minimum of 24 hours) before returning to dirt cup. use filter: FLTB for inner dirt cup.  
Dirt Cup Cover  
*HEPA Filter is located  
INSIDE the green filter  
protector. Remove filter  
protector to access  
HEPA Filter.  
Tap Gently  
Filter Protector  
Body  
r
*
HEPA  
Inner Filter  
(Located inside  
Filter Protector)  
Fig. 21  
Fig. 22  
Dirt Cup  
ExHAUST FILTER CLEANING & REPLACEMENT  
Dirt Cup  
Release Button  
pull out the exhaust filter. (Fig. 23)  
Fig. 19  
replace the exhaust filter when it becomes dirty. (Fig. 24)  
use filter: FLTA for exhaust filter.  
NoTE: This filter is washable.  
Filter Frame  
Filter  
Dirt Cup  
Release Button  
-
Exhaust  
Filter  
Body  
Fig. 24  
Fig. 20  
Fig. 23  
NoTE: Replacement parts can be purchased by calling  
1.866.603.5900 or by visiting www.germguardian.com.  
E-11  
E-10  
 
BELT REPLACEMENT  
TRoUBLESHooTING GUIDE  
WARNING: BEFoRE REPLACING THE BELT, MAKE SURE THE CLEANER  
IS UNPLUGGED FRoM THE ELECTRICAL oUTLET.  
Please check each item below if you have trouble with your vacuum.  
Before checking, always ensure that the vacuum is unplugged from the power supply.  
Turn oFF the cleaner and unplug from electrical outlet.  
remove the bottom plate of the base by removing the five (5) screws using a  
phillips screwdriver. (Fig. 25)  
PRoBLEM  
PRoBLEM  
SoLUTIoN  
Set the new belt over motor pulley. (Fig. 26) use replacement belt: BLT1.  
Slip the brush roll into the belt and reassemble. (Fig. 27)  
replace the bottom plate and secure the 5 screws.  
Vacuum won't run.  
1. Power cord not firmly plugged  
into the outlet.  
2. Motor protector tripped.  
1. Plug in unit firmly.  
2. Cool down and press the RESET button.  
(See page 3)  
3. Needs service.  
3. Take to service center or call 1.866.603.5900.  
Brush roll won't spin. 1. Vacuum is not in the  
UPRIGHT mode.  
1. The brush only turns on when the handle is  
released for vacuuming. The brush does not come  
on in the UPRIGHT position even if the switch is  
ON. Depress handle for brushroll to start turning.  
Motor Pulley  
2. Make sure the brush switch is ON.  
3. Remove it and clean debris, hair, etc. off of  
brush, then replace.  
2. Brush switch is OFF.  
3. Brush roll is jammed.  
Fig. 25  
Fig. 26  
Fig. 27  
4. Replace the new belt or correct the belt's securing.  
(See page 11)  
4. Belt is broken or off  
motor pulley.  
HEADLIGHT REPLACEMENT  
Vacuum or tool won't  
pick up dirt.  
1. Rotate height adjustment knob to correct height  
setting. (See page 6)  
2A. Check hose connection and make sure it is  
attached to proper inlet: base inlet on body  
(UPRIGHT) or inlet on handle (CANISTER/TOOLS).  
2B. Grasp hose tube and firmly push onto base.  
3. Try to remove clog by squeezing out of hose.  
1. Incorrect height setting.  
2. Hose not attached to:  
WARNING: BEFoRE REPLACING THE HEADLIGHT, MAKE SURE THE CLEANER  
IS UNPLUGGED FRoM THE ELECTRICAL oUTLET.  
Turn oFF the cleaner and unplug from electrical outlet.  
press the handle release pedal and use the handle to place the body in a flat position.  
remove the headlight cover by removing the screw with a phillips screwdriver. (Fig. 28)  
pull the bulb straight out of the socket. (Fig. 29)  
A. Inlet  
B. Base.  
3. Clogged hose.  
4. Dirt cup is full.  
4. Empty dirt cup (see page 9); if washed, after  
dried well, reinsert it.  
install the new bulb, model lbu.  
replace the headlight cover and secure the screw.  
5. Clean or replace with new. (See page 10)  
6. Take to service center or call 1.866.603.5900.  
5. Inner filter is blocked.  
6. Crack or hole in hose.  
Headlight  
Cover  
Headlight  
Vacuum is difficult  
to push.  
1. Incorrect height setting.  
2. Brush switch is OFF.  
1. Rotate height adjustment knob to correct height  
setting. (See page 6)  
2. Make sure the brush switch is ON.  
Visible dust escaping 1. Dirt cup is full.  
from vacuum.  
1. Empty dirt cup (see page 9); wash it, after dried  
well, replace it.  
2. Filter missing or incorrectly  
2. Check inner filter and exhaust filter for  
correct installation.  
Fig. 28  
Fig. 29  
installed.  
3. Dirt cup installed incorrectly.  
3. Pull out and re-insert dirt cup correctly.  
NoTE: Replacement parts can be purchased by calling  
1.866.603.5900 or by visiting www.germguardian.com.  
E-13  
E-12  
 
LIMITED WARRANTy  
To the consumer, Guardian Technologies llc warrants this product to be free of  
defects in materials and workmanship commencing upon the date of the original  
purchase. Save your original sales receipt to validate start of warranty period.  
if this product should become defective within the warranty period, we will repair  
or replace any defective parts free of charge. The complete machine must be  
delivered pre-paid to any authorized Guardian Technologies llc warranty service  
center. please include complete information on the problem, date of purchase, copy  
of original sales receipt and your name, address and telephone number. if you are  
not near a warranty station, call the factory for assistance in the uS and canada at  
1.866.603.5900. use only genuine Guardian Technologies' replacement parts.  
The warranty does not include unusual wear, damage resulting from accident  
or unreasonable use of the product. This warranty does noT cover bulbs. This  
warranty does noT cover unauthorized repairs. This warranty gives you specific  
legal rights and you may have other rights (other rights may vary from state to  
state in the u.S.a).  
We consider the registration process important to ensuring superior service to our  
customers, however submitting this card to Guardian Technologies llc is optional  
and does not affect your right to utilize this warranty according to the conditions  
above. if you have any questions or comments about our product call Toll Free at  
1.866.603.5900 or send comments to:  
ATTN Customer Service  
Guardian Technologies LLC  
7700 St. Clair Avenue  
Mentor, ohio 44060  
Guardian Technologies LLC  
7700 St Clair Avenue | Mentor Ohio 44060  
1.866.603.5900 | www.germguardian.com  
E-14  
 

Haier Dishwasher WQP12 EFMS User Manual
Haier TV Receiver LT19A1 User Manual
Hamilton Beach Beverage Dispenser Coffee Urn User Manual
Hamilton Beach Juicer 67650 User Manual
Hamilton Beach Toaster 22502 User Manual
Hans Grohe Car Video System HL190 User Manual
HP Hewlett Packard All in One Printer PSC1100P User Manual
HTC Cell Phone EVO4G User Manual
Humminbird SONAR HDR600 User Manual
iHome MP3 Docking Station iH70 User Manual